200-150 practice test

1. Question 1 · 1

   What is the maximum distance that is supported by Cisco passive Twinax cables?

   Choose one answer.

   • 3 m
   • 4 m
   • 5 m
   • 10 m

2. Question 2 · 1

   What is the maximum distance that is supported by Cisco active Twinax cables?

   Choose one answer.

   • 8 m
   • 10 m
   • 12 m
   • 15 m

3. Question 3 · 1

   If a Nexus switch receives a frame and does not have an entry in its MAC table for the source, which action will take place?

   Choose one answer.

   • The frame will be dropped.
   • The frame will be flooded.
   • The sender will be notified.
   • The source address will be learned.

4. Question 4 · 1

   How many IP addresses are usable for a subnet that has the address 10.6.128.0/21?

   Choose one answer.

   • 1024
   • 2048
   • 1022
   • 2046
   • 256

5. Question 5 · 1

   What is the maximum distance that is supported between two devices that are connected via Cisco Fabric Extender Transceivers?

   Choose one answer.

   • 50 m
   • 75 m
   • 100 m
   • 150 m

6. Question 6 · 1

   What is the minimum number of fabric modules that should be installed in the Cisco Nexus 7000 chassis for N 1 redundancy using M1-Series line card?

   Choose one answer.

   • 3
   • 4
   • 5
   • 6

7. Question 7 · 1

   In an IEEE 802.3 Ethernet frame, what is the significance of the DSAP field?

   Choose one answer.

   • The DSAP field specifies the TCP or UDP port that is associated with the transport protocol.
   • The DSAP field is only used on United States Department of Defense networks to indicate the information classification level.
   • The DSAP field is only used in Ethernet II frames.
   • The DSAP field indicates the network layer protocol.

8. Question 8 · 1

   What is the maximum number of fabric modules that can be installed in a Cisco Nexus 7000 chassis?

   Choose one answer.

   • 4
   • 5
   • 6
   • 7

9. Question 9 · 1

   How many supervisor engines must a Cisco Nexus chassis contain to support the In-Service Software Update feature?

   Choose one answer.

   • 2
   • 3
   • 4
   • 1

10. Question 10 · 1

    Ethernet 1/1 is assigned IP address 10.1.1.1 with subnet mask 255.255.255.0. Which configuration is used to configure EIGRP on a Cisco Nexus 7000 switch?

    Choose one answer.

    • feature eigrp ! interface Ethernet1/1 ip address 10.1.1.1 255.255.255.0 no shutdown ! router eigrp 1 network 10.1.1.0 0.0.0.255
    • feature eigrp ! router eigrp 1 autonomous-system 1 ! interface Ethernet1/1 ip address 10.1.1.1/24 ip router eigrp 1 no shutdown
    • router eigrp 1 autonomous-system 1 ! interface Ethernet1/1 ip address 10.1.1.1/24 ip router eigrp 1 no shutdown
    • feature eigrp ! interface Ethernet1/1 ip address 10.1.1.1/24 no shutdown ! router eigrp 1

11. Question 11 · 1

    VLAN 10 is assigned IP address 10.1.1.1 with subnet mask 255.255.255.0. Which configuration is used to route the IP subnet but not form OSPF neighbors on a Cisco Nexus 7000 switch?

    Choose one answer.

    • feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ip router ospf 1 ip passive-interface ospf 1 ! router ospf 1
    • feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ! router ospf 1 passive-interface default no ip passive-interface Vlan10
    • feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ! router ospf 1 ip passive-interface Vlan10
    • feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ip router ospf 1 !

12. Question 12 · 1

    The kickstart image is corrupted on a Cisco Nexus 7000 switch. Which procedure is used to download a new kickstart image?

    Choose one answer.

    • Boot the system and press Ctrl-] while the memory test is in progress to interrupt the boot loader.
    • Boot the system and press the Esc key while the memory test is in progress to interrupt the boot loader.
    • Boot the system and press the Esc key after the BIOS memory test to interrupt the boot loader.
    • Boot the system and press Ctrl-] after the BIOS memory test to interrupt the boot loader.

13. Question 13 · 1

    Which situation results in a flashing blue status LED on a Cisco Nexus 7000 switch I/O module?

    Choose one answer.

    • The switch has just been powered on, and the module is resetting.
    • The module is resetting and both ejector levers are out.
    • The module has been inserted during the initialization process.
    • The module could not power up because of insufficient power.
    • The operator has activated this LED to identify this module in the chassis.

14. Question 14 · 1

    Which two features must be licensed on a Cisco Nexus 7000 Switch? (Choose two.)

    Choose all answers that apply.

    • Layer 3
    • Virtual Device Contexts
    • Virtual Port Channel
    • Fibre Channel

15. Question 15 · 1

    Which two features must be licensed on a Cisco Nexus 5548UP Switch? (Choose two.)

    Choose all answers that apply.

    • Virtual Port Channel
    • Fibre Channel
    • FabricPath
    • iSCSI

Paid access to all 46 questions

Each purchase applies to this certification. Prices are one-time payments, not monthly subscriptions.