300-610 practice test

1. Question 1 · 1

   An engineer must connect an existing Cisco UCS Fabric Interconnect to an IP-based storage array. The connection must be a port channel made directly between the fabric interconnect expansion module and the storage array. The engineer must also consider that the environment is running FCoE for storage and uses QoS to prioritize traffic. Which port type should be used to meet these requirements?

   Choose one answer.

   • network
   • uplink
   • server
   • appliance

2. Question 2 · 1

   An engineer designs a Cisco UCS solution that must provide guaranteed and deterministic bandwidth to a specific server in the environment. The solution must apply to network and storage traffic of C-Series and B-Series servers. Which solution should be included to meet these requirements?

   Choose one answer.

   • Pin the vNICs and the vHBAs of the service profile to dedicated uplink ports.
   • Pin the IOM ports of the service profile to dedicated server ports.
   • Pin the server ports of the service profile to dedicated uplink ports.
   • Pin the vNICs and vHBAs of the service profile to dedicated server ports.

3. Question 3 · 1

   A network consultant evaluates the Cisco UCS Fabric Interconnect SAN configuration, which must meet these requirements: • All traffic must pass over the upstream device for switching and domain IDs must be preserved in the fabric. • Each server should be pinned to one designated upstream interface and for the traffic to pass through the pinned port. Which Fabric Interconnect SAN operational mode meets these requirements?

   Choose one answer.

   • end host
   • switch
   • NPIV
   • Fibre Channel

4. Question 4 · 1

   An engineer is implementing a Cisco UCS environment. The system must aggregate all vNICs into a single policy and consistently enforce node disassociation across the cluster. Which two UCS policies meet these requirements? (Choose two.)

   Choose all answers that apply.

   • scrub policy
   • vNIC policy
   • boot policy
   • firmware policy
   • LAN connectivity policy

5. Question 5 · 1

   A cloud service provider is managing day-2 operations of over 200 blade servers installed in the Cisco UCS environment. This pool of network resources is providing virtual networks to their customers. To successfully operate this environment, frequent changes to vNICs and other operational policies are required across multiple UCS domains. The operations team must streamline these repetitive tasks. Which orchestration tool must be used to meet this requirement?

   Choose one answer.

   • Cisco ACI Multisite Orchestrator
   • Cisco DNA Center
   • Cisco UCS Director
   • Cisco UCS Manager

6. Question 6 · 1

   An engineer must integrate Layer 4 to Layer 7 services within Cisco ACI Fabric. The main requirement is to have a single point of configuration for network elements and firewall policies. Which action meets these requirements?

   Choose one answer.

   • Define the service graph model as network policy mode.
   • Deploy the firewalls in routed mode with PBR.
   • Deploy the firewalls in transparent mode.
   • Define the service graph model as service policy mode.

7. Question 7 · 1

   Which protocol prevents fiber failures from causing a Layer 2 loop in a dark fiber DCI?

   Choose one answer.

   • BFD
   • UDLD
   • MCP
   • LLDP

8. Question 8 · 1

   A cloud provider deploys an infrastructure based on Cisco ACI Fabric, Cisco UCS, and Cisco HyperFlex Data Platform. The storage area network will be based on Cisco MDS 9000 Series Switches with Hyper-V, VMware, and KVM used as the virtualization platform. The requirement is to deploy the overall solution by using a robust automation and orchestration tool. Which tool meets these requirements?

   Choose one answer.

   • Cisco Prime Infrastructure
   • Cisco Network Assurance
   • Cisco UCS Director
   • Cisco Cloud Center

9. Question 9 · 1

   An engineer must design a Cisco HyperFlex solution to support a virtualized environment in a single data center location. The design must consider these customer requirements: • a large-scale cluster with eight or more nodes • distributed high-performance file system for virtualized servers • high fault tolerance to multiple node failures Which action meets these objectives?

   Choose one answer.

   • Configure data destaging and deduplication.
   • Implement a replication factor of four.
   • Enable logical availability zones.
   • Create multiple datastores for storage of VM.

10. Question 10 · 1

    A Cisco UCS chassis with several blade servers, a pair of IOMs, and a pair of Cisco UCS Fabric Interconnects are installed in a data center. Which two high-availability architectures are recommended between the IOMs and fabric interconnects? (Choose two.)

    Choose all answers that apply.

    • One, two, four and eight links are supported to be used between each IOM and fabric interconnect.
    • IOM A is connected to the fabric interconnect that is acting as fabric A, and IOM B is connected to the fabric interconnect that is acting as fabric B.
    • Any combination of one to eight links is supported to be used between each IOM and fabric interconnect.
    • The IOMs are connected with multiple straight and cross-connect links toward a pair of nonclustered fabric interconnects.
    • Straight and cross-connect links should be used between the IOMs and fabric interconnects to offer higher availability.

11. Question 11 · 1

    A network consultant must design a high availability interconnection of a clustered Cisco UCS Fabric Interconnect toward two upstream Layer 2 switches. The Ethernet interconnection must use all redundant links and have no impact on the STP domain size. Which connectivity solution must be used?

    Choose one answer.

    • Cisco UCS Fabric Interconnect in switch mode with dual uplinks distributed evenly to the upstream switches
    • Cisco UCS Fabric Interconnect in switch mode with a single uplink toward each upstream switch to eliminate any change to the STP domain size
    • Cisco UCS Fabric Interconnect in end host mode with a single uplink toward each upstream switch to eliminate any change to the STP domain size
    • Cisco UCS Fabric Interconnect in end host mode with dual uplinks distributed evenly to the upstream switches

12. Question 12 · 1

    An engineer is expanding an existing iSCSI environment and must choose an addressing scheme. When checking one of the devices, the engineer discovers this target device naming used: {prefix}.2019-01.com.acme123:00.ffd0cb21.bcb392817521 Which addressing scheme was used in the environment?

    Choose one answer.

    • Network Address Authority
    • Extended Unique Identifier
    • iSCSI Qualified Name
    • Fibre Channel ID

13. Question 13 · 1

    A storage engineer requires a solution that achieves multiple paths between a server and storage array. The design must support complete traffic isolation and support a 50% growth in the next year. Which FCoE solution meets these requirements?

    Choose one answer.

    • single switch with multiple links
    • at least two VSANs across the fabric
    • at least two FC zone sets with multiple zones
    • single VSAN across the fabric

14. Question 14 · 1

    Refer to the exhibit. A high-availability setup for iSCSI is designed with the host running iSCSI multipath software. Each IP storage port on the MDS switch exports the same two Fibre Channel target ports with different iSCSI target names. In this design, how many iSCSI sessions are created from the host so that recovery occurs if any component fails?

    Choose one answer.

    

    • 2
    • 3
    • 4
    • 5

15. Question 15 · 1

    A network architect designs a high-availability architecture for the Cisco UCS Fabric Interconnects that are installed in a data center. The architecture must support clustering and redundancy. Which architecture meets these requirements?

    Choose one answer.

    • dual connections from port L1 to L1 and one connection from port L1 to L1 with twinax cables
    • dual connections from port L1 to L2 and one connection from port L2 to L1 with twinax cables
    • dual connections from port L1 to L2 and one connection from port L2 to L1 with Ethernet cables
    • dual connections from port L1 to L1 and one connection from port L2 to L2 with Ethernet cables

Paid access to all 111 questions

Each purchase applies to this certification. Prices are one-time payments, not monthly subscriptions.